How do I program my 9241 Remote?

To operate your TV

1. Locate the remote programming code (PDF 3.41 MB) for your TV.
2. Press and hold TV until SAT, AUX and VCR light up.
3. Release TV. It will start to flash.
4. Enter one of the codes for your TV model, then press #. TV should flash three times.
5. Try to control your TV.

Does the Bell receiver 9241 need a smart card?

You do not need a smart card.

How do I connect my bell 9241 receiver?

How to set up your replacement receiver

1. 9241 – HD PVR Plus Receiver.
2. Disconnect your old receiver and connect the replacement using the same cables.
3. Turn your receiver and TV on.
4. Wait about 2 to 4 minutes until the Point Dish screen is displayed.
5. Select Check Switch with your Bell TV remote.
6. Select Test.

How do I reset my bell receiver 9241?

9241 – HD PVR Plus Receiver

1. If you can’t see any picture on your TV, reset your receiver by pressing and holding the POWER button for 5 seconds.
2. On your Satellite TV remote, press MENU.
3. Scroll to and select System Setup.
4. Scroll to and select Factory Defaults.
5. Read the warning and select Yes.

How do I find my TV remote code?

How to Find a Code for My Remote Control

1. Look through the User’s Manual for your remote control to find the code section.
2. Go to an website listing code, such as the Remote Code List (See References).
3. Call the manufacture of your remote and ask whether it can tell you the codes you need.

How do I program my remote to my TV?

Turn on your TV or another device you wish to control. Press and hold the corresponding DEVICE and POWER buttons on the remote at the same time. Wait until the power button comes on and then release both buttons. Pointing the remote at the TV or another device, press the Power button on the remote and wait 2 seconds.

How do I run a check switch on Bell Satellite?

Select Check Switch with your Bell TV remote. If you are not on the Point Dish screen, press Menu then 6-1-1 with your remote (or use the front panel buttons) to access it. Select Test. Wait about 1 to 5 minutes until the receiver completes the test.

How do I activate my bell receiver?

1. Call 1 866 353-03341 866 353-0334. 2. Choose the Activate an additional receiver option from the self-serve prompts.

How do I reboot my bell receiver?

Reboot your receiver

1. Press and hold-down the green POWER button on the front of your TV receiver for 5 seconds (until the red, green, and blue lights come on).
2. Wait a few minutes for the reboot to take place.
3. Once the reboot completes, content from the channel that you last viewed appears.

How do I find my TV code without a remote?

Even without the remote guide, you can perform an automatic code search with the remote to find the correct code:

1. Press TV once (or the desired device).
2. Press and hold SETUP until the TV button blinks twice.
3. Enter 9-9-1: the TV button will blink twice.
4. Press CH+ repeatedly until the device turns off.

Where to find the Bell ExpressVu 9241 receiver manual?

If you are looking for the Bell 9241 manual, you can visit the Bell support site and obtain the manual in PDF format here – http://www.bell.ca/support/PrsCSrvTv_DTHHelp_9241Guides.page#1.

Why is my Bell PVR 9241 not working?

Bell 9241 HD PVR Deal! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

Where can I buy Bell PVR in Canada?

Find Bell Pvr in Canada | Visit Kijiji Classifieds to buy, sell, or trade almost anything! Switched to Fibe TV Complete with Remote and User Guide. Bell. That’s okay though because you can add your own review and we’ll feature it here. Bell 9241 HD PVR Deal! – YouTube Bell 9241 HD PVR Deal!

Which is the best guide for Bell TV receivers?

Great on-screen guide Bell TV receivers feature the most advanced onscreen guide. Choose between p and i HD resolutions. With a 9 days in advance programming guide you will have access to your programs onscreen. If playback doesn’t begin shortly, try restarting your device.