What is a 10 meter beacon?

10-meter beacons Most high frequency radio propagation beacons are found in the 10-meter band (28 MHz), where they are good indicators of Sporadic E ionospheric propagation. According to IARU bandplans, the following 28 MHz frequencies are allocated to radio propagation beacons: IARU Region. Beacon Sub-bands (MHz)

What is the 10 meter calling frequency?

28.0-28.5 MHz
10 meters is unique—the band from 28.0-28.5 MHz being where all licensed US radio amateurs from Novice through Extra Class have voice and digital mode privileges.

What is the range of a 10 meter radio?

28.000 to 29.700 MHz
The 10-meter band is a portion of the shortwave radio spectrum internationally allocated to amateur radio and amateur satellite use on a primary basis. The band consists of frequencies stretching from 28.000 to 29.700 MHz.

What is 10 meter radio used for?

10 Meter Radios are Amateur Radios, also known as Ham Radios. Another important aspect of operating a 10 Meter Radio is that they don’t want disruption of other important communications. With their high power output, 10 Meter Radios can overpower CB transmissions and other important local communications.

What is a beacon frequency?

Beacon is transmitted once on each frequency, from low (14.100 MHz) to high (28

What frequency is WWV on?

WWV operates in the high frequency (HF) portion of the radio spectrum. The station radiates 10 000 W on 5 MHz, 10 MHz, and 15 MHz; and 2500 W on 2.5 MHz and 20 MHz. Each frequency is broadcast from a separate transmitter.

What is the 2 meter calling frequency?

For new hams who are likely to get started in local VHF/UHF operation, the national calling frequencies to be concerned with are 2m and 70cm FM simplex (non-repeater). These are 146.520MHz and 446.000MHz, respectively, and should be included in your radio’s scanned channels.

Do you call CQ on 2m?

The 2m FM voice calling channel is 145.500MHz and the 70cm FM voice calling channel is 433.500MHz. Here’s how to use them: Tune to the calling channel, and listen to make sure it’s not in use. Call CQ, making sure you give your callsign clearly and concisely.

Are there 10 meter repeaters?

Most 10-meter repeaters use +/- 5 kHz deviation. The frequency 29.600 MHz is the accepted “calling frequency” for North and South America.

What are the 11 meter frequencies?

The U.S. 11-Meter Citizen Band Extends from 26960 to 27410 kHz.

What does 42 mean in trucker talk?

CB Radio Code and Lingo at CB World

CB Terminology Meaning or Translation
FM An AM/FM radio.
42 Yes, or OK.
Four-Letter Word Nobody wants to stop at the weigh station- that is why “OPEN” is considered a four-letter word in the trucking industry. When the weigh station is open.
Four Wheeler Any passenger vehicle with four wheels.

Are radio beacons still used?

Radio-navigation beacons Due to relatively low purchase, maintenance and calibration cost, NDBs are still used to mark locations of smaller aerodromes and important helicopter landing sites. Marine beacons, based on the same technology and installed in coastal areas, have also been used by ships at sea.

Are there any beacons on the 10m band?

An excellent way of checking band conditions on the 10m band are the beacons which you can locate on that band. Most beacons operate in CW and transmit their identification (call sign and location). Below is a list of Australian 10m beacons.

What are the specifications of a 10 meter beacon?

TP2CE Beacon – TP2CE/B rtx at 28.222.8 Mhz, using 450 mW into a GP R-7000 post your report. VA2MGL Beacons – Info and specifications on my three beacons on 10 and 6 meter bands.

Where are the 10 meter beacons in Argentina?

CORDOVA, ARGENTINA # Uncoordinated beacon reported 21 March 09 28.190 LU1DZ I BUENOS AIRES,ARG # 10W,VERTICAL (temp?) 28.1901 LU1XZ ?

How to request a frequency for wi5v Beacon?